Tips On How To Extend Smok Pen Recharge Time
The Smok Pen is a new pen that was developed by two guys in California. They wanted to develop a cool writing instrument that looked like a real pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the market by storm.
The Smok Pen has a built quality that’s just great. I found that even though it is an electronic pen the construction is just as good as any of the pens that I have reviewed. Simply because of how they made the very best cap. You don’t have to be worried about podsmall.com the cap cracking or breaking you Smok Valve Pen.
Both biggest differences that separate the Smok Valve from other pens may be the form of the coils and just how that they are built. In general the coil on a Smok Pen is bigger than on other pens. I believe that they did this on purpose, to make the pen feel bigger.
Invest the a glance at a Smok Pen, you will notice that the body of the pen is round rather than smooth like other pens. On the back of the pen there exists a little tab that houses the coil. Once you press on the tab it is simple to turn the heating element on and off. I must say i liked this feature since it allows me to utilize the Smok Pen 22 whenever I feel like smoking.
To use the Smok Pen you need to keep carefully the heat button pressed. Once the button is pressed, the heating element will begin to warm up. Once it gets to the appropriate temperature you can turn off the heating element. Smok recommends utilizing a 22mm tank. I prefer a larger tank, but that’s just me.
Once you put your Smok Pen into the tank you will see a indicator light seriously. The indicator light will remain green unless you put your Smok Pen in to the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is important to always put your pen into the charger before you apply the e-liquids to the coil heads. It is also important to do this before putting your e-liquids in to the coil heads.
After you have completed this step, it is best to check to see for anyone who is at the proper temperature for the coils to fire. Or even then you should turn the energy off and try again. For anyone who is still not satisfied together with your Smok Pen i quickly suggest you take it in for some troubleshooting. This is what I’d call the “troubleshooting process” because sometimes things just do not work as they should. It is suggested that you perform the next two steps, then go on and check the Smok Pen to see if it still has the electronic charging port.
Before you go any further you should remove the battery from your pen and unscrew the magnetic cap. You should then remove the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body that is green in color. You need to loosen this wire using pliers. When you have loosened this wire you can then access the sub-ohm. You need to then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful never to touch any of the coils.
After you have placed the sub-ohm tank into the pen you need to then place all of those other components like the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Start the energy and follow the on screen instructions. You should place the pen’s battery in to the microwave and activate the setting. You should then wait approximately 30 seconds before turning it cool off. When you initially put the pen into the microwave the electronic reading will show a low voltage protection setting. If this setting does not automatically get set you then should follow the on screen instructions.
Once the Smok Pen has reached the temperature that it requires to reach you should then connect both wires to the positive and negative on the positive post on the Smok unit. You should then connect the other end of the battery to the negative post on the negative side of the Smok unit. The ultimate step would be to connect the positive cable to underneath of the Smok’s on / off switch.
After all the components have been placed in to the pen, you should turn the power on. Following the first test run, you should be able to see the battery life indicator light come on. If you do not see any sign of life from the Smok Pen, you should remove the battery from the pen and replace it with a fresh one. For your convenience there is also a green light that could be pressed so as to confirm the battery charging status. If you have done these things and you also do not see the green light indicating charging, you need to replace the battery.